|
|
| 你的位置:知识库首页-> 许国璋英语 |
| |
焊接专业英语词汇(1) - 机电工程词汇
作者:张进 阅读次数:3572
| |
| |
| |
熔接fusion welding
压接pressure welding
焊接过程welding process
焊接技术welding technique
焊接工艺welding technology/procedure
焊接操作welding operation
焊接顺序welding sequence
焊接方向direction of welding
焊接位置welding position
熔敷顺序build-up sequence
deposition sequence
焊缝倾角weld slope/inclination of weld axis
焊缝转角weld rotation/angle of rotation
平焊位置flat position of welding
横焊位置horizontal position of welding
立焊位置vertical position of welding
仰焊位置overhead position of welding
平焊downhand welding/flat position welding
横焊horizontal position welding
立焊vertical position welding
仰焊overhead position welding
全位置焊all position welding：熔焊时，焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。如水平固定管所进行的环缝焊接
向下立焊vertical down welding/downward welding in the vertical position
向上立焊vertical up welding/upward welding in the vertical position
倾斜焊inclined position welding
上坡焊upward welding in the inclined position
下坡焊downward welding in the inclined position
对接焊butt welding
角焊fillet welding
搭接焊lap welding
船形焊fillet welding in the downhand position/fillet welding in the flat position
平角焊horizontal fillet welding
立角焊fillet welding in the vertical position
仰角焊fillet welding in the overhead position
坡口焊groove welding
I形坡口对接焊square butt welding
喇叭形坡口焊 flare groove welding
卷边焊flanged edge welding
纵缝焊接welding of longitudinal seam
横缝焊接welding of transverse seam
环缝焊接girth welding/ circumferential
螺旋缝焊接welding of spiral seam/welding of helical seam
环缝对接焊butt welding of circumferential seam
定位焊tack welding
单面焊welding by one side
双面焊welding by both sides
单道焊single pass welding/single run welding
多道焊multi-pass welding
单层焊single layer welding
多层焊multi-layer welding
分段多层焊block sequence/ block welding
分层多道焊multi-layer and multi-pass welding
连续焊continuous welding
断续焊intermittent welding
打底焊backing weld
封底焊back sealing weld
盖面焊cosmetic welding
深熔焊deep penetration welding
摆动焊welding with weaving/weave bead welding
前倾焊 foreward welding (英国)/ forehand welding (美国)
后倾焊 backward welding(英国)/ backhand welding(美国)
分段退焊backstep welding
跳焊skip welding
对称焊balanced welding/ balanced welding sequence
左焊法leftward welding forehand welding
右焊法rightward welding/backhand welding
挑弧焊whipping method
自动焊automatic welding
手工焊manual welding/hand welding
车间焊接shop welding
工地焊接site welding(英国)/ field welding (美国)
拘束焊接restraint welding
堆焊surfacing/building up/overlaying
隔离层堆焊buttering
端部周边焊boxing/end return
返修焊rewelding
补焊repair welding
塞焊plug welding
槽焊slot welding
衬垫焊welding with backing
焊剂垫焊welding with flux backing
窄间隙焊narrow-gap welding
强制成形焊enclosed welding
脉冲电弧焊pulsed are welding
电弧点焊arc spot welding
螺柱焊stud welding
热风焊hot gas welding
高能焊high grade energy welding
固态焊接solid-state welding
单面焊双面成形one-side welding with back formation
焊接条件welding condition
焊接工艺参数welding parameter
极性polarity
正接electrode negative/straight polarity
反接electrode positive/reversed polarity
运条方式manipulation of electrode
焊接电流welding current
焊接电流增加时间welding current upslope time
焊接电流衰减时间welding current downslope time
电流密度current density
短路电流short circuit current
脉冲电流pulse level/pulse current level
脉冲电流幅值pulse current amplitude
基值电流background level
脉冲频率pulse frequency
脉冲焊接电流占空比duty cycle of pulse duration
电弧电压arc voltage
再引弧电压reignition voltage
焊接速度welding speed
行走速度rate of travel/travel speed
送丝速度wire feed rate
线能量heat input/energy input
热输入heat input
预热preheat
后热postheat
焊后热处理posweld heat treatment/postheat treatment
预热温度preheat temperature
层间温度interpass temperature
焊接终了温度finishing temperature
后热温度postheating temperature
焊丝伸出长度wire extension
弧长arc length
熔化速度melting rate
熔化时间melting time
熔化系数melting coefficient
熔敷速度rate of deposition/deposition rate
熔敷系数deposition coefficient
熔敷效率deposition efficiency
损失系数loss coefficient
飞spatter
飞溅率spatter loss coefficient
融合比fusion ratio
稀释dilution
稀释率rate of dilution
合金过度系数transfer efficiency/recovery (of an element)
坡口groove
坡口面groove face
坡口面角度angle of bevel (英国)/ bevel angle (美国)
坡口角度included angle(英国)/groove angle(美国)
坡口高度groove depth
钝边root face
钝边高度thickness of root face/width of root face
根部间隙root gap(英国)/root opening (美国)
根部半径root radius/groove radius
根部锐边root edge
卷边高度height of flange
卷边半径radius of flange
单面坡口single groove
双面坡口double groove
坡口形式groove type
I形坡口square groove
V形坡口single V groove
Y形坡口single V groove with root face
双Y形坡口double Vgroove with root face
带钝边U形坡口single U groove
带钝边双U形坡口double U groove
VY形坡口single compound angle groove
带钝边J形坡口single J groove
带钝边双J形坡口double J groove
单边V形坡口single bevel groove
双V形坡口double V groove
不对称双V形坡口 asymmetric double V groove
双单边V形坡口 double bevel groove/K groove
带垫板V形坡口 V groove with backing/ single V groove with backing
关键字:机电工程词汇 | | | | |
| |
| |
| |
|
|